Heavy scale deposits can also lead to localised overheating of heat transfer surfaces, resulting in premature failure of heating appliances.
In all areas, rust and corrosion may take place in heating and cooling systems, leading to a build up of corrosion deposits and a reduction in efficiency.
Well a power flush or descale could be for you
Some of the benefits:
It restores heating system efficiency.
It restores heat output to radiators.
It solves flow & circulation problems.
It cleans the WHOLE system including under floor pipe work.
It minimizes boiler warranty problems and is more effective than traditional flushing methods.
It can be done in only ONE visit!
It can save you money on heating bills and repairs



Services:

We can descale, Power flush, jet Flush, Powerflush your installation removing scale, sludge and mineral deposits from your central heating system returning them to a much better efficiency.

'POWER FLUSHING' 'JET FLUSHING' &
'HARD FLUSHING'...
...are all expressions used (in the heating trade over many years) to denote the process by which heating systems are forcibly cleansed using water at high velocity, but low pressure, so that no physical damage is caused to the system. The process can be made even more effective with the addition of powerful cleansing and mobilising agents such as FX2 and HYPER-FLUSH, from Kamco.

The objective is to restore systems with circulation and boiler noise problems (caused by sludge and corrosion deposits) to optimum operation. Power flushing removes these deposits and the problems that they cause.

Power flushing, in conjunction with SYSTEM PRE-CLEAN, is also an excellent way to pre-commission clean new heating systems, to remove excess flux, swarf and other debris, and the grease and oil used to prevent rusting of components before use.

It is prudent to power flush a heating system immediately before fitting a new boiler to an existing system to prevent possible future problems. Many systems are found to contain corrosion and sludge, even if no flow problems have yet shown themselves.

Existing debris is often mobilised by alterations to the system/piping and the increased efficiency of the new boiler, and may then accumulate in the boiler heat exchanger, causing noisy operation, reduced efficiency and, in extreme circumstances, failure of the boiler. The high efficiency and compactness of modern boilers, developed to minimise fuel costs and pollution, means that they are more susceptible to problems caused by debris in the system water.


The Power Flushing process is a versatile, easy to use and highly effective method of flushing heating systems. Heating systems can be purged of sludge, scale and corrosion deposits with minimal dismantling and disruption.

Is Power Flushing necessary?
Power flushing is the process of running high volume and low pressure water through a heating system to remove scale, rust and foreign objects, using mains water and usually an acidic chemical,
If you have problems with the radiators being cold, or just cold at the bottom or little or no hot water, this maybe the solution for you.

HOW DOES IT WORK?
The Power Flushing pump is simply connected into the heating system, either across standard circulator pump couplings, across the tails of one radiator, or wherever most practicable. The powerful flow, combined with instantaneous flow reverser device, will dislodge and mobilise deposits and corrosion which resist traditional system cleaning methods.
Once the corrosion and sludge deposits have been loosened and mobilised, fresh clean water is forced through the heating system, pushing the contaminated water out through a full bore dump valve to waste. During the process, radiators are individually flushed, without removing or disconnecting them from the system, by directing the full output of the pump through each radiator separately.
At the end of the flushing process, the system contains fresh clean water and reinstatement of the system to normal operation takes only a few minutes.
System flushing will not remedy design or mechanical faults, which should be rectified, but in many cases it will cure the problems caused by these.
What's the difference between a descaling pump and a power flushing pump?
Can I use a descaling pump for power flushing?

Most smaller descaling pumps are not powerful enough to effectively flush a central heating system. They don't have the vital flow rate or the pressure needed to maintain flow against the resistance of the heating system.

We have the right tools and we know how to use them.